The paint process is actually a very deep knowledge. It is said that the three-point carpentry is a seven-point paint, so the brush paint must cause everyone's attention, and a little carelessness will affect the effect of the entire wall. The following Xiaobian introduced the paint brushing precautions for everyone.
Paint process considerations 
Paint process precautions First, prevent too dry
During the painting process of the paint, attention should be paid to changes in the humidity of the air. If the humidity is too high, the paint will dry very slowly. This will not only affect the progress of the project, but will also affect the quality of painting and painting in the interior decoration; and if it is too dry, It will cause the paint to dry too quickly and cracks will appear.
Paint process considerations Second, dark paint should pay attention
If you prefer a darker living space, you will naturally choose darker paints. It is important to note that when using dark paints, do not add any thinner to the paint. This guarantees to a large extent The color of the paint we used did not show a color difference. If we notice a color difference, the whole room would be hard to read.
Pay attention to the paint process Third, pay attention to fire prevention in the dry season
Paints such as paints are relatively flammable and explosive. Therefore, in the dry season, special attention should be paid to fire prevention to avoid unexpected accidents. At the same time, when selecting paints and other materials, it is necessary to pay more attention to the relevant standards of the country. Some of the paints do not seem to have much problems, but they are not strictly enforced according to national standards and are also very dangerous to use.
Paint Process Precautions IV. Stain on the Paint Surface
The appearance of stains on the surface of the paint is very aesthetically pleasing. We must pay more attention to these problems during paint construction and avoid affecting the overall appearance. When we encounter such a problem, we must analyze the root cause of the problem and find out the reasons before we can solve it. We can apply a layer of primer containing aluminum powder to the part that is to be painted before painting begins. This will largely avoid similar problems.
Paint Paint Brushing Steps 1, first remove the clean wood products on the gray layer, dirt, etc., to keep the surface clean and tidy.
2. Polish the base layer, trim the defects such as burrs and cracks on the surface of the wood base layer, polish it with sandpaper, and keep corners neat.
3. Use a transparent putty or oily putty to scrape, re-suppress the putty, polish it with coarse sandpaper, wait until it's dry, put it on the second pass, and polish it with fine sandpaper.
4, brushing paint, refilling putty, dry with a fine sandpaper, remove the surface dust; then on the second pass paint, remove the surface dust after grinding and water sand for water, repair oil hanging part; Three times can paint.
Problems with Paint Processes First, paint off
The problem of paint shedding is more often encountered because the surface of the object is too smooth. This usually checks two reasons:
1, paint. If the original paint is lacquer or is powdery, the new paint brush will not stick well. This can add untreated paste paint.
2, or wood decay or metal rust, the surface of the object is not clean and sure paint is not strong, which requires sanding, rust or spoilage parts.
Second, paint foaming
When the paint is foaming, it is necessary to first observe the bubble pierced. If there is water below the bubble, it means that the wall has moisture intrusion. Use a hot air gun to remove the starting paint. After the wood is naturally dry, brush it with a primer and then fix it. Repaint the surface. If there is no water under the bubble, the foamed paint is first scraped off, and the resin filler is used to fill in the crack and repaint it.
Third, there is a crack
The crack is often encountered in the paint process. If the crack area is not large, you can use sandpaper to dip the water, rub the paint off until it is smooth, then put on the putty, brush the primer, dry it and repaint it. If the area of ​​the crack is large, remove the paint completely with a chemical paint remover or hot air gun and repaint it.
Fourth, moldy discoloration
Mouldy discoloration is due to too humid, in addition to ventilation and drying, but also use fungicides, according to instructions, after the treatment, the paint surface clean and repaint.
Five, brush paint considerations
1, the paint can not be brushed too thick, otherwise it will cause the paint to flow, it seems that the table is not smooth (can be sanded).
2. If stains appear on the wall, first remove the paint at the stains, brush the primer with aluminum powder, and then re-paint.
3, brush the second time the paint must wait for the first time the paint completely dry, or prone to wrinkling phenomenon of the film.
4. The well-painted surface should be covered with a cover or cardboard when the paint is dry to prevent dusting and affecting the appearance.
To learn more about paint brands, please click here to view this site http:// paint brand Daquan , thousands of paint brands do in it.
paint
MDCP IS Pulverized white powder or grey powder or granule,Tasteless,Odorless.Packaging:25kgnet of Bag and 1000kg supersack (PP woven),Storage and Transport:It should be stored in a cool,dry,and ventilated places.It should be kept away from rain and sunshine during transport.It shelf life is eternity.MDCP is mainly used as additive in feed to meet the little livestock's requirement on absorbing Phosphate and Calcium.
Mono Dicalcium Phosphate (MDCP)
Mono Dicalcium Phosphate,Mdcp Powder,Mdcp White Powder,Mdcp Grey Powder
MIDI FEED BIOTECH LIMITED , https://www.chinabromine.com