Before installing the fire pump , it should be noted that there is no problem in determining the cable it needs. This is more basic. In addition, it is also guaranteed that the insulation resistance of the motor should reach the specified value. Secondly, careful inspection of the tightening of the guide rods, including all details of the parts, must be intact and without looseness. A small problem that has not been checked or is not recovered in time will greatly affect the subsequent operations. After checking, let's take a look at the installation process, also need to pay attention to:
1. When lifting the fire pump, a stainless steel chain should be used. The stainless steel material is very firm and will not rust for a long period of time. Safety is guaranteed. During installation, the stainless steel chain should be lifted from beginning to end.
2. The exit area of ​​the fire pump should be connected with a metal hose, or the steel pipe can be used because of the high pressure of the water pump. The pipe connected to the pump outlet, whether it is a metal hose or the other, must ensure its length, so as to extend the pool as a standard, which will make it easier to dismantle. In many places, the installation of pumps is performed by professionals. These specifications, including the parts used, are professionally equipped. When installing, the most important thing is to comply with the installation regulations, follow the rules step by step, and do a detailed inspection.
3, the pump outlet should be installed hose check valve, etc., which is clearly defined by the relevant provisions. Because no matter what the instrument is, it will undergo many trials and adjustments before it is used in the market. The relevant regulations and values ​​are not out of thin air. All the contents of the explanation items are well documented.
4. Between the outlet pipe and the ground, in order to prevent the deformation or damage of the fire pump, the support should be determined so that even if the pump is installed for a long time, it will not be easily damaged.
Coal Activated Carbon For Gas Purification
Gas purification using coal-activated carbon for chemical raw gas, chemical synthesis gas, pharmaceutical industrial gases, beverages with carbon dioxide gas and hydrogen, nitrogen, ozone, ethyl hydrocarbon, ethane, butane, cracking gas, inert gases, such as purification and atomic installation of exhaust gas purification. Also used to remove contaminants in the air, as well as separation and purification of mixed gases. can also be used for gas masks and protective equipment disinfection and filtration.
Use: Used in the purification, seperation and refining of chemical raw material gas, chemical synthesis gas, pharmaceutical use gas, carbon dioxide for drinks, hydrogen, nitrogen, inert gases etc.
Spec.:
|
Model NO.
|
Moisture(%)
|
Strength(%)
|
Ash(%)
|
Carbon tetrachloride(%)
|
Packing density(g/L)
|
Grain diameter(mm)
|
| ZK-2050 |
≤3
|
≥95
|
≤8
|
≥50
|
580±20
|
Φ2.0
|
| ZK-2060 |
≤3
|
≥95
|
≤10
|
≥60
|
530±20
|
Φ2.0
|
| ZK-2070 |
≤3
|
≥95
|
≤10
|
≥70
|
510±20
|
Φ2.0
|
| ZK-3050 |
≤3
|
≥95
|
≤10
|
≥50
|
540±20
|
Φ3.0
|
| ZK-3060 |
≤3
|
≥95
|
≤10
|
≥60
|
510±20
|
Φ3.0
|
| ZK-3070 |
≤3
|
≥95
|
≤12
|
≥70
|
500±20
|
Φ3.0
|
| ZK-3080 |
≤3
|
≥95
|
≤12
|
≥80
|
460±20
|
Φ3.0
|
| ZK-4050 |
≤3
|
≥95
|
≤10
|
≥50
|
530±20
|
Φ4.0
|
| ZK-4060 |
≤3
|
≥95
|
≤10
|
≥60
|
510±20
|
Φ4.0
|
| ZK-4070 |
≤3
|
≥95
|
≤10
|
≥70
|
490±20
|
Φ4.0
|
| ZK-5060 |
≤3
|
≥95
|
≤10
|
≥60
|
500±20
|
Φ5.0
|
Coal Activated Carbon For Gas Purification
Coal Activated Carbon For Gas Purification,Coal Activated Carbon,Gas Purification Coal Activated Carbon,Coal Based Powder Activated Carbon
SHIZUISHAN ZhongShi activated carbon co,.ltd , https://www.zscarbonchina.com