1, a bottom diameter of the solar street light pole, a bottom flange size should meet the design requirements. If there are special requirements, the manufacturer shall provide detailed drawings of the corresponding products for Party A and design considerations.
2. The inside and outside of the solar street lamp post should be treated by hot dip galvanized inner and outer surface anti-corrosion and other processes. Yangzhou Sino-American New Energy Lighting has learned that the galvanized layer should not be too thick, the surface has no color difference and roughness. The above anti-corrosion treatment process should meet the corresponding national standards. During the construction process, anti-corrosion test reports and quality inspection reports on the light poles should be provided.
3. The surface of the solar street lamp pole needs to be color sprayed, and the color should meet the requirements of the owner. Spray paint should use high-grade paint.
4. The pole of solar street lamp shall be calculated according to the wind speed force specified in the national standard, and the force requirements. During the construction process, material descriptions and stress calculation books related to the light pole shall be provided. Yangzhou Sino-US New Energy Lighting recommends that for lamp poles that are welded with steel rims, the contractor should clean the welded joints before welding and make a bevel according to the regulations.
5. The hand hole door of the ordinary street lamp pole of solar street lamp, the design of the hand hole door should be beautiful and elegant. The door is plasma cut. The appliance door should be integrated with the rod body, and the structural strength should be good. With reasonable operation space, there are electrical installation accessories in the door. The gap between the door and the rod should not exceed one millimeter, with good waterproof performance. There is a special fastening system with good anti-theft performance. The electrical door should have high interchangeability.
6. The installation of solar street light poles shall comply with the relevant regulations in the relevant national installation regulations and safety regulations. Yangzhou Sino-US New Energy Lighting recommends that before installation, the pole should be selected according to the height, weight, and site conditions of the pole, and the location and displacement and correction method of the suspension point should be reported to the supervision engineer for approval ; Two directions perpendicular to each other are equipped with instruments to check and calibrate to ensure that the position of the lamp pole is correct and the shaft is vertical.
7. When the solar street lamp is connected by bolts, the screw should be perpendicular to the penetration surface, there should be no gap between the screw head plane and the component, and there should be no more than 2 washers at each end . After the bolt is screwed, the length of the exposed nut is not less than two Pitch.
8. After the installation and correction of the solar street lamp pole, the contractor shall immediately carry out backfill tamping. The backfill tamping shall comply with the relevant regulations.
9. The installation of solar street lamp power discharge pipes shall comply with the drawings and relevant specifications.
10. Verticality inspection of solar street lamps: After the pole is upright, use the theodolite to check the verticality between the pole and the horizontal.
11. The overall appearance of the solar street lamp pole: the shape and size meet the requirements, the overall appearance is elegant, the surface of the pole body is smooth and consistent, and the color is uniform.
Yangzhou solar street lamp manufacturers mainly produce and sell: solar street lamp series, led street lamp series, high pole lamp series, Chinese lamp series, courtyard lamp series, lawn lamp series, various other special street lamp series, undertake road lighting projects, etc.,
Yangzhou street lamp manufacturers, solar street lamp price consultation telephone, 15050780308
Website: http: //
Graphite Electrodes mainly use needle coke, Petroleum Coke, as raw material, coal pitch as binder, calcination, ingredients, kneading, molding, baking and graphitization, machining and made, which is released in electric arc furnace in the form of arc conductor of electricity to heat melting furnace charge, Graphite Electrode with low resistivity, graphite electrode good conductivity, graphite electrode low ash, graphite electrode uniform and compact structure, good oxidation resistance, high mechanical strength, etc.
Uhp 650 Graphite Electrode,650Mm Uhp Graphite Electrode,650Mm Graphite Electrode,Graphite Electrodes 650Mm Diameter
Carbographite Industrial PTE.LTD , https://www.carbographite.com