Ceiling construction in kitchens and toilets has always been a difficulty in home decoration. Because the humidity is relatively large during this period, there are fumes and odors. At the same time, the hustle and bustle of life makes people can not clean up the sundries in the kitchen and toilet in time. Therefore, choosing suitable materials and reasonable construction methods in the ceiling decoration construction can reduce a lot of trouble for future life.
During the construction process, waterproof coatings, PVC sheets and aluminum-plastic panels are commonly used materials in kitchen bathroom ceilings. Waterproof coating has the characteristics of convenient construction, low cost, and diverse color in construction. After long-term use, there is a phenomenon of local shedding and fading, performance is also more unstable, and less used in home decorating.
PVC sheet is used more often in homes now, construction is also convenient and fast, and the color is rich. The most important feature is that the waterproof performance is good, easy to clean, and long-term use does not need to be replaced. However, because PVC sheet is an extrusion molding material, the traces of industrialized machinery production are more obvious, lack of personalization, less change, and the indoor environment has a sense of less coordination, lower grades.
Long strip aluminum plate
In recent years, the increasingly popular material is aluminum-plastic plate and other types of materials, with a light aluminum sheet stamping molding, the outer layer and then spray the plastic with a special process, colorful rich, long-term use does not fade, waterproof performance is excellent, the construction is simple and not deformed . But relatively high cost, generally used in high-end places such as apartments, combined with marble, granite and other natural stone laying walls, not only bring out their own decorative features, but also harmonious and unified, complement each other.
For the ceiling construction of kitchens and toilets, the selection of suitable materials is only the first step, and the main process of the construction process is the arrangement of exhaust air and humidity, so that the indoor damp air can be discharged in time. On the one hand, it can protect the ceiling material and its structure. On the other hand, it effectively protects the increasing electrical equipment in the kitchen and bathroom, and it also provides more convenience for cleaning work.
Nowadays, there is a tendency for aluminum gusset material to replace PVC material with strong plastic feel. Let's take a look at the installation process of aluminum gusset ceiling.
Do a good job of scaffolding before ceiling
Half-mounted aluminum buckle ceiling
The installation method of PVC suspended ceiling profiles is very simple. First, the elevation line should be popped up on the wall, the pressure lines should be fixed at both ends of the wall, and the concrete nail should be firmly fixed with the wall. The board is cut according to the actual size of the ceiling. The board is inserted into the battens. The slats are flush with the outside of the slats. After the installation, the nails are fixed with nails.
Corrective keel
Install the second board Note the balance
Insert the second board. The last board should be cut in accordance with the actual size. When cutting, use a sharp knife, press the elastic wire with a steel rule to cut it, insert it into the upper board to make a slight bend, insert the seal on both sides. .
Check the keel
Ceiling acceptance plan
1, according to the design elevation of the ceiling on the wall around the bomb, the horizontal allowable deviation of ± 5mm.
2, around the corner of the plastic corner with a real corner line, tight seams, and the wall around the tight, uniform gaps.
3. The types, specifications, colors and basic structure of the materials used in the ceiling project shall be in accordance with the design and relevant specifications.
4. The panel and keel should be tightly connected. The surface should be flat and there must be no defects such as pollution, cracking, missing corners, and hammer injuries. Joints should be uniform and consistent in color.
5, ceiling panel construction brush coating, quality should meet the quality requirements of wall paint.
Fasten
Worker tears off protective film on packaging
Ceiling process requirements
1. When fixing with nails, the nail distance should not be greater than 200mm. The plastic buckle plate is neatly stitched, flat, no color, no deformation, and no stain.
2, wooden keel ceiling wood is not less than 25mm × 30mm, and wooden rules. And meet the paper plaster wood keel process requirements.
3, the panel and the wall, curtain boxes, lamps and other junctions should be tight, there must be no leakage phenomenon, light fixtures (and exhaust fans) should be closely connected with the keel, heavy lamps or ceiling fans, shall not be connected with the ceiling keel, should be in the base board Another hanging piece.
Ceiling Mounting Coatings Home Decor Interior Decorating Decoration Designs High Grade Curtains Ceiling Fan Lights Kitchens Bathroom Ceilings Toilet Ceilings Material Toilet Sizes Bathroom Ceilings Toilet Designs Toilet Waterproof Apartments Renovation Decoration Home
TORICH is focusing on Honed Tube manufacturing and exporting,
ID Honed Tube is produced by cold drawing on stainless steel or carbon steel over a mandrel,
seamless honed tube where the surface is honed or skiving roller burnish, and the tubes are stress relieved and annealed if it is necessary.
The Steel Tubes are produced according to technical standard of
EN10305-1 Cold Drawn Seamless Steeel Tubes
EN10305-2 Cold Drawn Welded Precision Steel Tubes
Seamless and Welded DOM tubing are produced by material of E155,E195,E235,E275,E355 +C +LC +SR +A +N
DOM is a process that is applied to tubing after it is initially constructed.
It is referred to as Seamless ,It can be said that do seamless process method on ERW tubes,
So the tubes will have a high strength ,high quality.
DOM tubing is commonly use in auto parts and machinery parts, also for heavy engineering industry.
Big Diameter Honed Tube, Skiving Roller Burnished Tube, max ID 650mm, max length 12000mm
Production facility for ID Honed and Skiving Roller Burnished Steel Tube
ERW mother tube for Honed Tube
Seamless Steel Tubes in Cold Drawn Production for ID Skiving Roller Burnish Production:
Stainless Steel Pipe ready for ID Honing
Honed Finish ID for Stainless Steel Pipe:
Honed Tube
Honed Tube,High Precision Honed Tube,Honing Hydraulic Cylinder Tube,Carbon Steel Honed Tube
Torich International Co.,Ltd--The Steel Tube Maker , http://www.chinasteeltubepipe.com