When it comes to radiators, everyone should know more or less. So what about the heat sink ? How is it different from floor heating? How should I use it? Next, Xiao Bian gave everyone an explanation and hoped to help everyone.
Insert Heatsink - Introduction
The insert radiator adopts straight pipe push inflation machine to expand the pipe so that the aluminum profile wall and the liner can achieve plastic deformation. The rebound is tight, the surface is smooth, and the dimensional accuracy is high. The plug assembly can achieve 100% leakage. Therefore, there is no waste generated in the production process to reduce energy waste. In addition, welding is not required during the assembly process, and there is no overheating effect on the surface of the insert radiator, which saves a lot of manpower and energy. In addition, the insert heat sink is not assembled with the required process leak liner, the overall strength is high, and deformation and leakage are not caused due to careless installation.
What is the difference between insert radiator and floor heating?
The first point is that it is much more troublesome to install and maintain the floor heating than to insert the radiator. Floor heating is buried under the floor. Ideally, it can be warm with the building. However, if unforeseen problems occur, it is very troublesome. It is necessary to turn this floor over and the human and material resources spent are not worth it. In contrast, the insert radiator does not have this problem, and now the new aluminum radiator is exposed to the air, and some are hung on the wall, the problem is very easy to repair, replacement is also more convenient, on this point In fact, the advantages of inserting a radiator are unmatched.
The second point is that long-term use of floor heating can damage the body's circulatory system and can cause some respiratory diseases. As there are a lot of viruses and bacteria on the floor, they will be very active and cause diseases when the floor is heated. The use of a heatsink to insert the panel is to convectively heat the air and then pass it to the human body, which will not cause the above phenomenon. For the family's health, it is a very reasonable method to use the insert radiator to heat.
The third point is that the damage to the floor and furniture in the room is relatively large, and it is easy for them to age and fade. If there are expensive wooden furniture in the home, it is recommended that you do not use warm floor heating, which is very detrimental to the maintenance of the furniture. If you replace the insert radiator, the installation position is relatively arbitrary, and the distance to the furniture can also be adjusted very well. It will not cause aging due to the specific furniture, so it is very good to protect them.
How to use the heat sink
If the insert heatsink is used improperly, it is not conducive to our normal winter heating. Although the heating insert radiator is simple in production process, if there is no correct use method, the heating effect will be greatly reduced. The following Xiao Bian will give you a brief introduction on how to use the heat sink properly. I hope to provide you with some help!
1. The position of the insert heat sink must be reasonable: there must be no shield in front of the insert heat sink, which will affect the heat dissipation effect of the insert heat sink;
2. The surface of the insert heat sink is painted: The surface of the heat sink should be properly selected. A large proportion of the external surface of the heat sink is based on radiation. The external heat radiation accounts for 50% of the total heat transfer. , Then there are 50% are spread out by the right, is a comprehensive performance of the two heat transfer methods. Therefore, in order to avoid reducing the heat dissipation effect, surface painting should be avoided as much as possible.
3, can not put things on the insert heat sink, this will give the impact of convection affect the equipment from the surface effect.
Summary: There are many types of heat sinks for the current inserter. For the majority of users, when selecting, it is necessary to clarify the specific application and select according to the characteristics of the product. Want to know more about insert heatsink introduction, please continue to pay attention to this site information.
Floor heating pipe leaking warm leak water heating pipe heating pipe brand floor heating what good floor
Ultrafine Silica Median Particle Size 2~4
Ultrafine Silica Median Particle Size 2~4,Silicon Oxide Powder,Silicon Carbide Powder,Silicon Dioxide Powder
Changxing Wanxing Building Material Co., Ltd. , https://www.wxbuildingmaterials.com