Certainly! Here's the rewritten content in English:
---
**1. Overheating of the Motor Stator and Excessive Body Temperature (Exceeding Rated Temperature Rise)**
When the motor stator overheats and its temperature rises above normal levels, it’s crucial to take immediate action:
- **Step 1:** Stop operation immediately and allow the motor to cool naturally.
- **Step 2:** Dry the motor promptly to prevent moisture damage.
- **Step 3:** Investigate the root cause of the overheating, such as excessive load, and adjust accordingly.
- **Step 4:** Use a multimeter to check and correct any electrical issues.
- **Step 5:** Insulate damaged areas with insulating tape or cloth.
- **Step 6:** Reconnect loose wires carefully and ensure all connections are secure.
**2. Strong Dull Sound, Reduced Speed, and Decreased Vibration Force**
If the motor emits a dull noise, slows down, and vibrates less, follow these steps:
- **Step 1:** Disassemble the motor for thorough inspection and repair.
- **Step 2:** Replace blown fuses and fix any open circuits.
- **Step 3:** If the motor coil is burned out, partially or fully rewind the stator coil.
**3. Electrical Charging of the Motor or Handle**
When the motor or handle becomes electrically charged, address the issue as follows:
- **Step 1:** Insulate cracks on the surface using electrical tape.
- **Step 2:** Conduct a detailed inspection of the coil and replace any damaged sections.
**4. Sparking Switches and Frequent Fuse Breakage**
For switches that spark and fuses that frequently break:
- **Step 1:** Inspect and repair the switch thoroughly.
- **Step 2:** Perform drying procedures to eliminate moisture.
- **Step 3:** Adjust the load to prevent overloading.
**5. Damaged Rolling Bearings in the Electric Wire and Rotor-Stator Friction**
If the rolling bearings are damaged and there’s friction between the rotor and stator:
- **Step 1:** Replace the faulty rolling bearings immediately.
**6. Sluggish Vibrating Rod**
When the vibrating rod moves sluggishly:
- **Step 1:** Change the wiring by swapping any two phases.
- **Step 2:** Inspect the one-way clutch and replace or repair parts if needed.
- **Step 3:** Ensure all connectors are properly connected.
- **Step 4:** Resolder or replace the flexible shaft.
- **Step 5:** Clean the flexible hinges, remove oil stains from the rollers and raceways, and replace the rubber oil seal if required.
**7. Difficulty in Vibrating the Vibrating Rod**
If the vibrating rod fails to operate smoothly:
- **Step 1:** Adjust the power supply voltage to ensure stable performance.
- **Step 2:** Replace the vibrator housing, clean the rolling bearings, and refill with grease.
- **Step 3:** Clean or replace the rolling bearings, and either replace or tighten the top cover.
- **Step 4:** Gently tap the rod head or lightly touch its tip to the ground.
- **Step 5:** Remove oil stains and replace the oil seal if necessary.
- **Step 6:** Repair the flexible shaft and adjust the length of the hose spring for optimal alignment.
**8. Broken Rubber Casing**
In case of a broken rubber casing:
- **Step 1:** Cut out the damaged section, reconnect it, or install a new hose.
- **Step 2:** Address unusual metallic sounds inside the attached vibrator by relocking it and replacing the locking bolt if needed.
**9. Difficulty Vibrating the Base Plate of a Flat-Panel Vibrator**
If the base plate of a flat-panel vibrator struggles to vibrate:
- **Step 1:** Replace the rolling bearings.
- **Step 2:** Adjust or replace the rubber pads under the motor base, and adjust or replace the vibration-damping springs.
This comprehensive guide ensures that you can troubleshoot and resolve common issues effectively while maintaining equipment safety and longevity.
---
I hope this version meets your requirements! Let me know if further adjustments are needed.
Miniature sensor, small size, small range, high precision, easy to install. With advanced sealing technology, the sealing grade reaches IP65, and it can work in high humidity environments; it has a single-hole structure and double-hole structure; it has bending deformation structure and shear deformation structure. Widely used in automatic testing, medical equipment, control technology equipment, etc.
Miniature Load Cells,Small Load Cells,Mini Load Cells,Load Cell Tension Compression
Zhejiang Nanhua Electronic Technology Co., Ltd , https://www.nhloadcell.com