Prevention and control of dead peppers in summer

Summer peppers are mainly caused by stem-based rot, blight, root rot, heat and rain. Some are caused by high temperature and rain in summer, drought, etc., should first determine the cause of the death of the pepper, and then symptomatic treatment.

 

Capsicum blight: The performance is that the plant grows slowly during the flowering period, and the lower leaves turn yellow and gradually develop upward. At noon, the leaves were wilting and recovered at night. After repeated days, the whole plant died of wilting. Sometimes half of the disease occurs, and half of the plants are healthy. When the disease develops rapidly, the whole plant is wilting. The epidermis of the stem of the diseased plant has multiple longitudinal fissures, yellow-brown streaks at the nodes and internodes, and rosin-like gums often flow out. When wet, it grows white and pink mildew. It can be seen that the vascular bundle and the roots turn yellowish brown and rot, and it is easy to pull up from the soil. Crossing the diseased stem, the vascular bundle was brown.

 

Capsicum root rot: In the onset period, the lesions on the stems of the near-ground are water-stained, slightly sunken, and then rotted, and the main lateral roots are all rotted and died. The disease is only harmful to the roots and does not develop upwards.

 

Pepper stem rot: performance begins with a large seedling and occurs severely after colonization. The lesion appeared at the base of the stem near the ground, initially dark brown, and then developed around the base of the stem, causing the cortex to rot, and the upper part of the leaf turned yellow. During the fruit expansion period, it gradually disappeared due to insufficient supply of nutrients and water. External causes: Due to continuous cropping, the bacteria in the soil accumulate too much, and the ground temperature is too high.

 

Another factor that causes seriousness is that the seedling age is getting bigger and bigger when planting, and the overgrown ground is not noticed when planting, and the plant shakes badly, which is easy to cause wounds at the base of the stem. Plus the cover of the mulch, the shelves, the introduction of vines and other management, resulting in more wounds, causing dead trees.

 

All of the above three diseases are infected by fungi, which can survive for many years in the soil and occur severely in continuous cropping.

 

Control method:

 

　　 1. Rotation and rotation of non-solanthous fruit crops for 3 to 5 years. The seedbed should be exchanged for 2 to 3 years, or replaced with new soil.

 

　　 2 , seed seedlings should be sterilized before germination, commonly used methods are: warm soup soaking; dry heat treatment, dry seeds in a constant temperature of 70 ° C ~ 75 ° C for 5 to 7 days.

 

　　 3 , cultivation management selection of high-potential field cultivation, try to use ridges, sorghum or semi-high sorghum planting; control the amount of watering, timely drainage in the rainy season to prevent mites; fertilization pay attention to the application of nitrogen, phosphorus, potassium to prevent lack of fertilizer or More nitrogen fertilizer.

 

At the time of planting, attention should be paid to eliminating diseased plants and reducing the incidence after colonization. When planting, try to use seedlings with smaller seedling age to reduce mechanical damage.

 

In the management process of planting, covering the mulch, and putting on the shelves, take it lightly and gently, and try to avoid causing wounds. After colonization, at the beginning of the disease, seed dressing double herbs were applied at the base of the stem. In order to reduce the wound, try not to cultivate the soil during the growing season.

 

4 , the initial stage of drug control can be used 50% carbendazim WP 500 times solution, or 50% methyl thiophanate 400 times solution; can also use 48% Swift worm water 800 times solution, each plant root irrigation 0.25 kg liquid, once every 10 days, 2 to 3 times.

 

Source: Inner Mongolia Agriculture and Animal Husbandry Information Network

 

 

 

 

 

Full Power Emergency Battery Pack

The Full power emergency pack is ideal for LED tubes 3-40W Full power emergency output wattage for LED emergency lighting 60-180mins. Automatic lighting up when main power failures. Suitable for LED fitting with external led driver and internal driver. Widely using for parking lot, office, building, warehouse, school, hospital, workshop etc.

Emergency Lighting Battery Pack,Emergency Battery Pack For Led Lights,Emergency Power Packs,Bodine Battery Pack,led battery backup ballast

Foshan Nai An Lighting Electric Co.,ltd , https://www.fsnaipsled.com